Видео

I think I’ll get 32s when I wear out my factory ones a bit more . I road , Indian Ridge , Pinnacle creek , Pocahontas last year with My Talon R . No problem with my tires yet . I tried the Bob-t nap thing . My tablet wouldn’t overlay the maps . I recommend On X Off-road . I love it . The first few times I did Hatfield McCoy with the paper maps . The Tablet takes it to another level ! See you at the Outlaw bar and grill 😂👍

Bought mine yesterday July-2024 ,used it , should have read the directions 🥸, but it works fine, thanks for no stupid music 🎶 ah

This video was the deciding factor of my purchase of this stand, and I haven't regretted a second of it...except for the assembly instructions. To say that it's coming in extremely handy now that I'm having to rehuild the floor of a pool deck would be a gross understatement. This and the 10" miter saw is making short work of cutting the lumber to the perfect size and angle while dodging these damn pop-up Florida thunderstorms that happen throughout the day EVERY day. Wheeling it in before the storm starts is a breeze...no pun intended.

@popo's woodworks do you need spacers on the back wheels? I just bought the 31x10x15 carnivores... I'm planning to keep the stock wheels...

Greetings from Poland! I don't have steamer but steam from iron is also effective ;) Thank you for this idea

will this hold 130 lbs?

Wouldn’t a hair dryer do the same?

What offset were you running on all 4 wheels check out terrachie Aztecs they are a very light mud tire

I've just bought a router for the first time and your video was terrific. Nice commentary and making me more confident about my first project. Love your accent! I'm Aussie BTW. You did a good job on your first sign.

It's good for the first time

Super.The reason why the second leg had a 2mm gap while screwing is lack of enough pressure. If you had a timbre with clamp and when the top is wedged between the timbre and the leg then it would be bang on . Nevertheless you did end up with a nice table.Super kreg gig.

Wagner power stripper

Yes very good work nicely done

That is well done, good work, perhaps you could have clean up between the letters with a small chisel

Why is it not possible to place it on the burners?

Just stumbled on your video and enjoyed it. I plan on building something similar so if you are still around may I ask where did you get the TBL decal?

Looks great

THANK YOU!!!!!!!!

For the power cnc thing, that’s a lot of work for a short swap. Seems faster to just re-probe

Got this and it lasted years. The wire wasted away and the thing shorted out before the gears broke. (Blew the fuse in the cigarette lighter)

Nice job !

Nice job I love the wood stove

Nice job man

Thank you

Nice stand, why use osb for the floor vs plywood? I see several people do this we’ve always used plywood

Made a queen version of this 4 years ago... about to do it again for a king! Best dimensional lumber DIY out there!

It’s too bad you didn’t clean up the back board before closing it up. Seeing the sticker and pencil lines kind of ruins it. Also, those Brad nails on the front make it look awful. Really need more patience when woodworking.

Good job

Yeah because everybody has a steamer like why can't people just make a video about what the title is

Nice work 👍👍

Great video! You're a good dad! And it's cool that you have the patience to let your 10 yr old paint by herself.

No scratch abrasive pads will clean emulsion ,oil based use alcohol wipes or white spirit

Clever idea. Go Hokies!

What size is your trailer

At about 1:50, you mention the end grain rings of your boards. As you lay your boards out next to each other, you should alternate them rings curved up and down, looking at them from the end. Your finished panel will be less likely to warp.

Is your EGA an STL file?

I really appreciate the tuto but my problem is a whole bucket of paint went on the floor

I built this bed, thanks for the great video! Now I’m working on copying your accent. 😂

15°

Did you like the router. Did it cut well. Enough power to geter done ?

Nice 👍

Frog was on point

I bought my Anzo from Cabela's during the clearance sale for 4.99. the limit was one. 😢

Damn she did a better job than I did and spilled less paint than I did and I’m 27

I worked at a flea market where a fellow did routed wood signs. He was good at it having done it for years. I can say for your first try your sign turned out great. It's just my opinion maybe, but hand wood worked pieces beat the machines. The slight imperfections when done by hand is art. Like out in nature, nothing is an exact copy of anything else. It wouldn't be nearly as beautiful if all the leaves and petals on the rose bush were exactly the same.

What a wonderful way to publically shame your daughter for making a mistake---and forcing her participate in the public humiliation. When she makes a mistake when she older, and one that she truly needs help to solve, I wonder if she'll come to you. I wouldn't. What a thing to say that it was a mistake to let her try something she really wanted to try and to announce this to the entire world right in front of her. How do you think she'll feel if her friends see this? Or her bullies?

Very good video!

You have inspired me with your efforts dear sir!!!! I'll be shopping for a cheap router tomorrow to get started on my sign.

How many pickets did you use

Awesome. Getting on it today . Thanks